Low-Power Electromagnetic Lock Fingerprint Access Control Mod Identification Door Switch Fingerprint Ignition Switch

Fingerprint Ignition Switch
$16.18
Quantity
Contact us

Get in touch

Please email us at sale1@rfid-life.com with a detailed overview of your project requirement. So that we can offer you the fastest and best support. You may expect a reply within 24 business hours. – Welcomes Your Comments And Questions.


Sales Department

Phone: +86 18205991243
Whatsapp: +86 18205991243
Telegram: +86 18205991243
Email: sale1@rfid-life.com
Address: No.987,High-Tech Park,Huli District,Xiamen,China


Support Department

Email: support@rfid-life.com


Business Hours

Monday - Friday 9am to 6pm

Saturday - 9am to 12am

Sunday - Closed

Description
Low-Power Electromagnetic Lock Fingerprint Access Control Mod Identification Door Switch Fingerprint Ignition Switch
Product Description

Note

1. This control board does not have a relay output, so the output of this control board is a voltage signal, not a switch signal. It is more suitable for controlling loads such as electromagnetic locks, safe locks, and locker locks. This control board does not have a motor drive chip, nor can it be used to control the forward and reverse rotation of the motor. 2. The maximum output current is 5A, Do not use over-range!
Specification
1
Control board wide voltage input, DC3.5V-DC15V are compatible (+ is positive,-is negative); control board size is 48*25*14mm in length, width and height.
2
The fingerprint head is equipped with a fingerprint module with 50 colorful lights. If you need a larger capacity fingerprint module, contact customer service, it can support up to 500 pieces.
3
Suitable for DIY users to modify, used in access control, cabinet lock control, industrial control and other occasions.
4
Can delete all ordinary user fingerprints or ordinary user fingerprints with a designated number; you can also restore the factory settings of fingerprints with one key.
5
Can freely choose the relay self-locking mode, jog mode, and ignition mode.
6
In jog mode, the time of relay control can be adjusted freely.
7
The recorded fingerprint information and the set jog time, relay mode, etc. will not be lost after power off.
8
Ultra-low power consumption standby current 10ua, suitable for battery power supply, standby time is more than 2 years.
9
The input voltage is equal to the output voltage of the control lock. If you want the control lock to output 12V, the input voltage also needs 12V. If you want the control lock to output 5V, the input voltage also needs 5V.
Installation Instructions

Basic operation

1. Press the button to restore factory settings: When the circuit board is powered on, keep pressing the "setting key" on the circuit board for more than 10 seconds, you can see that the red indicator light on the circuit board lights up and the fingerprint module starts to light up in white. At this time, release the "setting key" and fingerprint If the green light is always on for 1 second, it means the deletion is successful; if the fingerprint is always on for 1 second, it means the deletion has failed. After restoring the factory state, the system will clear all fingerprint libraries. At this time, the system is in demonstration mode, and any fingerprint can control the relay to open. 2. Recording the fingerprint of the administrator for the first time: [Maximum number of administrators is 10] When the system is in the factory state, press any finger on the fingerprint window and hold it for about 5 seconds without letting go. The yellow light of the fingerprint will light up. After the finger is removed, the yellow light will flash, and the operation of adding the administrator fingerprint will be entered. Start pressing the finger, the light blue light will turn on when the finger is pressed, the yellow light will flash when the finger is lifted, press the finger 4 to 6 times continuously, the green light will be on for about 3 seconds, the new fingerprint entry is successful; if the red light is on, it means entry fail. The yellow light continues to flash, you can continue to enter other fingerprints, if you need to end the entry, about 5 seconds without any operation will automatically exit. It is best to record a few more fingerprints for the first time to record the administrator's fingerprints, which is convenient for future use. The fingerprints that have already been registered are not allowed to be re-entered, the red light will be on, and the registration will be automatically exited. In the process of registering fingerprints, press the different edges of your fingers, so that the fingerprint recognition rate after registration is very high. If the red light flashes during the registration process, it prompts you to press with different edges of your finger, and you cannot use the same edge every time. 3. Enter more administrator fingerprints: You must use the administrator's fingerprint to press for more than 5 seconds and not release it until the yellow light turns on. After removing the finger, the yellow light flashes and enters the operation of adding fingerprint management. The entry process is the same as above. 4. Enter the fingerprints of ordinary users: [The maximum number of ordinary users is 490] You must use the management fingerprint to press for more than 10 seconds without releasing it. The yellow light turns on in turn, and the pink light turns on and then removes your finger. The pink light starts to flash, and enters the operation of adding ordinary user fingerprints. The entry process is the same as above. 5. Delete all fingerprints: You must press the administrator's fingerprint for more than 15 seconds without releasing it. The yellow light turns on and the pink light turns on. After the yellow light turns on for the second time, remove your finger and the yellow light flashes to enter the operation of deleting all fingerprints. At this time, press it again with any finger, the green light will be on for about 3 seconds, and all fingerprints have been deleted successfully. At this time, the system is restored to the factory settings, and any fingerprint can turn on the relay. 6. One key to unlock: The one-key unlock function is mainly used in the access control, and it is convenient to open the door with one key indoors. Connect a mechanical button to the "unlock button" of the circuit board. After pressing the button once (equivalent to the interface short connection), the output of the control lock will be automatically controlled, and the relay can be controlled without fingerprint verification. 7. Mode selection: [factory default is jog output mode] When the circuit board is powered on, after pressing the "set button" on the circuit board, the blue indicator light on the circuit board will flash, and the number of flashes represents different relay output modes. After pressing the button again, the number of flashes will cycle from 1 to 2 to 3. The blue light flashes once: it represents the relay self-locking output. After each unlocking is successful, change the long open and long close of the relay. The blue light flashes twice: represents the relay jog output. After each successful unlocking, the relay will be turned off automatically after turning on for 1 second. The factory default jog time is 1 second, and users can adjust other jog times by themselves. The blue light flashes for three seconds: it represents the relay ignition output. Each time the unlocking is successful, the relay is turned on. If the finger is kept pressed at this time, the relay will also be turned on until the finger is released, the relay is turned off. (Suitable for car and motorcycle ignition) 8. Relay jog time adjustment: [factory default jog time is 1 second] Press and hold the "set button" on the circuit board first, then turn on the circuit board input power, wait for the red and blue indicator lights on the circuit board to go out, then release the "set button". Then press the "set button" again, you can see the red indicator light starts to flash, and the number of flashes represents the corresponding timing time. After pressing the "Settings button" again, the number of flashes increases. At this time, press the fingerprint with your finger. After the verification is successful, the jog time will be automatically saved, and it will not be lost after the power is off. 1 flashing represents the timing of 300 milliseconds; 2 flashes representing the timing of 600 milliseconds; 3 flashes for 1 second; 4 flashes for 2 seconds; 5 flashes for 3 seconds; 6 flashes for 4 seconds; flashes 7 Time represents 5 seconds of timing; 8 blinks represents 10 seconds of timing; 9 blinks represents 60 seconds of timing; 10 blinks represents 15 minutes of timing; 9. Normally open and normally closed output of control lock: The control lock can be normally open or normally closed output, the user can choose these two modes according to different use occasions. The toggle switch NO on the control panel stands for normally open output, and NC stands for normally closed output. (The factory default is NO normally open output)
Details Images